All About Download 300-615 Test Question

NEW QUESTION 1

Refer to the exhibit. An engineer is troubleshooting why user1, user2, and user3 from group STORAGE-ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?

• A. Configure the role name to match the group name on Microsoft Active Directory.
• B. Include specific users into MDS role configuration.
• C. Configure SSH logins on Cisco MDS switch.
• D. Integrate Cisco MDS with Microsoft Active Directory.

Answer: A

NEW QUESTION 2
Refer to the exhibit. A network engineer configures an EEM script to get a syslog notification after a configuration change. This message appears when the engineer must make a new configuration to this switch. Which configuration did the engineer neglect to apply in the script for it to function properly?

• A. event cli match ‘configure terminal’
• B. event policy-default count 1 time 100
• C. event syslog occurs 10
• D. action 2.0 event-default

Answer: D

NEW QUESTION 3
After upgrading a client’s fabric interconnect to the latest version, an engineer discovers that the appliance has lost its entire configuration. Which two locations should an engineer check to confirm that the appliance had backed up the configuration prior to the upgrade in order to retrieve the lost configuration? (Choose two.)

• A. Equipment FSM page, InternalBackup stage
• B. Service profiles page, InternalBackup stage
• C. Admin page, PollInternalBackup stage
• D. Equipment FSM page, PollInternalBackup stage
• E. Admin page, InternalBackup stage.

Answer: AC

NEW QUESTION 4
Your client reports that many flaps and server cluster disconnects occur in their data center. While troubleshooting the issue, you discover a network attack hitting their Cisco Nexus 7000 Series Switches and determine that the source IP addresses are spoofed. Which first-line security solution resolves this issue?

• A. Dynamic ARP Inspection
• B. Unicast RPF
• C. IP Source Guard
• D. Storm Control

Answer: A

NEW QUESTION 5
One of Cisco Nexus Series interfaces has become errdisabled with the error message “DCX-No ACK in 100 PDUs”. What is the cause of this error?

• A. The host has not responded to the Control Sub-TLV DCBX exchanges of the switch.
• B. The acknowledgement number in the server response has not incremented for 100 exchanges.
• C. Cisco Discovery Protocol is disabled on the switch.
• D. LLDP is disabled on the switch.

Answer: B

NEW QUESTION 6
A vPC Type-1 inconsistency between two vPC peers in a VXLAN EVPN setup is discovered. Which two actions need to be attempted to resolve the issue? (Choose two.)

• A. Configure the NVE interfaces to be Up on both switches.
• B. Set a different distributed gateway virtual MAC address.
• C. Set a different secondary IP addresses on NVE source-interface.
• D. Configure the same VNI to multicast group maping.
• E. Set a different primary IP addresses on NVE source-interface.

Answer: AD

NEW QUESTION 7

Refer to the exhibit. An engineer is investigating a role mapping issue on a switch. The users report that they cannot view the IP addresses under the tenant “corp”. Which action resolves the issue?

• A. Add the users to the RADIUS server.
• B. Update the UNIX ID.
• C. Configure the correct secret password between the APIC and the RADIUS server.
• D. Add the updated avpair to include/corp/admin/

Answer: C

NEW QUESTION 8
An engineer is troubleshooting a failed DCBX exchange between a server and a Cisco Nexus switch. Which action allows DCBX to successfully negotiate?

• A. Enable ETS
• B. Enable PFC.
• C. Enable Cisco Discovery Protocol.
• D. Enable LLDP.

Answer: D

NEW QUESTION 9
You have an ACI environment with three APICs, two spine switches, and four-leaf switches. You wipe and reboot all APICs first then leaf and spine switches one-by-one and successfully go through the Initial Setuo dialogue on the APIC 1 CIMC KVM console. When you log in to the APIC1 WebGUI, you notice that you do not see any directly connected leaf switches being discovered under Fabric > Inventory > Fabric Membership. What is the cause of the issue?

• A. The leaf nodes were not erased properly, which caused a fabric parameters mismatch with the APIC1.
• B. Rebooting the APICs and the leaf and spine switches after wiping them is not required.
• C. You forgot to enter the TEP Pool value during the Initial Setup dialogue on APIC1.
• D. The same Fabric Name value should be used before after wiping all devices.

Answer: C

NEW QUESTION 10
A network administrator attempts to install an application in the Cisco NX-OS Guest shell and receives an error that there is not enough space on the disk. Which command must the administrator run to increase the disk space available in the Guest shell?

• A. guestshell growdisk rootfs [size-in-MB]
• B. guestshell pvextend rootfs [size-in-MB]
• C. guestshell resize rootfs [size-in-MB]
• D. guestshell resize2fs rootfs [size-in-MB]

Answer: C

NEW QUESTION 11

Refer to the exhibit. HSRP adjacency fails to form between Nexus7K-1 and Nexus7K-2. Which action should be taken to solve the problem?

• A. Configure preempt on one of the switches in the HSRP group.
• B. Configure the same HSRP priority between the two switches.
• C. Configure the correct subnet mask on Nexus7K-1.
• D. Configure HSRP version 2 on Nexus7K-2.

Answer: D

NEW QUESTION 12
Refer to the exhibit. Sw1 and Sw2 are two Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain. Which statement describes what happens in this scenario?

• A. Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them out to the underlay network through the uplink interfaces.
• B. Sw1 performs the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs.
• C. Sw1 and switch 2 perform the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs, depending on the hashing.
• D. Sw2 did not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VNI.

Answer: B

NEW QUESTION 13
DRAG DROP
Drag and drop the actions from the left onto the faults that they resolve on the right. Not all options are used.
Select and Place:

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 14

Refer to the exhibit. When an engineer inserts 8-Gb FC SFP port 15 on a Cisco UCS Fabric Interconnect, the port fails. What is a possible cause of the issue?

• A. Port 15 is configured as an Ethernet port.
• B. Port 15 is configured for 4-Gb FC.
• C. Port 15 is missing a license.
• D. The polarity of the fiber cable is reversed.

Answer: B

NEW QUESTION 15
A server administrator attempts to change the Cisco IMC KVM certificate to one signed by a private CA, but the certificate is not being accepted. What can cause this process to fail?

• A. using a certificate with a password-protected private key
• B. RSA encryption being used in the generation of the certificate.
• C. AES encryption being used in the generation of the certificate.
• D. public IP addres of the Cisco IMC not being included in the SAN.

Answer: A

NEW QUESTION 16
An engineer attempts to register Cisco UCS Manager to Cisco UCS Central, but the registration fails. The engineer can ping Cisco UCS Central from UCS Manager. Which two actions must the engineer attempt to resolve the problem? (Choose two.)

• A. Synchronize the date and time to NTP for Cisco UCS Central and the Cisco UCS domains.
• B. Apply the UCS Central license to UCS Central.
• C. Place Cisco UCS Manager on the same subnet as Cisco UCS Central.
• D. Allow port 443 between Cisco UCS Manager and Cisco UCS Central.
• E. Allow port 9443 between Cisco UCS Manager and Cisco UCS Central.

Answer: AD

NEW QUESTION 17
Refer to the exhibit. A switch is being downgraded to an earlier release because of a problem with the current release. After the switch is downgraded, it can no longer forward traffic. Which action resolves the issue?

• A. Enable ISSD after the downgrade is complete.
• B. Roll back to the original image.
• C. Reload the switch.
• D. Shut and no shut the interfaces to the FEX.

Answer: B

NEW QUESTION 18
Refer to the exhibit. A new Cisco Nexus 5548 Switch connects to a network. SAN switching is configured on the switch. The switch fc2/10 NP uplink is shown in the exhibit. Which action ensures that fc2/10 is in an up state?

• A. Replace the SFP port module in fc2/10.
• B. Configure the admin port type E on the upstream switch that connects the port.
• C. Enable NPIV on the upstream switch that connects the port.
• D. Configure the BB_credit buffers on the upstream switch that connects the port.

Answer: C

NEW QUESTION 19
Refer to the exhibit. The HSRP configuration in the exhibit fails to function. Which action resolves this issue?

• A. Enable IP redirects.
• B. Set the MTU to 1500 bytes.
• C. Configure HSRP version 2.
• D. Configure the same HSRP group on both devices.

Answer: A

NEW QUESTION 20
Cisco Unified Computing System Manager raises a critical error message that indicates that the system has overlapping Ethernet and FCoE VLANs. All of the Ethernet traffic on the overlapping VLANs drops. Which action resolves the issue?

• A. Modify the VLAN assignment to vNICs.
• B. Change the PIN groups on the vHBAs.
• C. Modify the FCoE VLAN.
• D. Set the FCoE VLAN as the native VLAN on server uplinks.

Answer: A

NEW QUESTION 21
......