All About Breathing IN101_V7 Testing Software

we provide Printable BICSI IN101_V7 training which are the best for clearing IN101_V7 test, and to get certified by BICSI BICSI Installer 1 Exam. The IN101_V7 Questions & Answers covers all the knowledge points of the real IN101_V7 exam. Crack your BICSI IN101_V7 Exam with latest dumps, guaranteed!

Online BICSI IN101_V7 free dumps demo Below:

NEW QUESTION 1
Which type of optical fiber cable should be color coded with an Orange outer cable sheath?

  • A. MM with a 100 um core diameter
  • B. Dispersion-shifted SM optical fiber
  • C. Polarization maintain SM optical fiber
  • D. SM optical fiber

Answer: A

NEW QUESTION 2
Light pulses in optical fiber cables are subjected to a loss in power as the light pulses travel along the optical fiber. Which of the following terms is used to describe this phenomenon?

  • A. Attenuation
  • B. Grounding
  • C. Crosstalk
  • D. Frequency

Answer: A

NEW QUESTION 3
How much cable slack should be left in the work area after termination?

  • A. 0.5m (1.6')
  • B. 1m (3.3')
  • C. 1.2 m (4')
  • D. 3m (10')

Answer: B

NEW QUESTION 4
Which of the following markings is used for non-conductive optical fiber general-purpose cables?

  • A. OFNG
  • B. OFCR
  • C. OFCP
  • D. OFNP

Answer: A

NEW QUESTION 5
Which of the following may provide a demarcation point between the service provider and the customer premises cabling?

  • A. Telecommunications room
  • B. Work area
  • C. Telecommunications enclosure
  • D. Entrance facility

Answer: D

NEW QUESTION 6
Which of the following is used to measure the length of a 4-pair cable?

  • A. Time domain reflectometer (TDR)
  • B. Pair scanner
  • C. Cable-end locator kit
  • D. Tone generator

Answer: A

NEW QUESTION 7
Which of the following attachment methods does BICSI recommend for attaching coaxial
connectors to coaxial cable?

  • A. Screw-on
  • B. Push-on
  • C. Compression
  • D. Crimp

Answer: C

NEW QUESTION 8
What grade of plywood is recommended for use with ICT systems?

  • A. A/C
  • B. A/D
  • C. C/D
  • D. B/C

Answer: A

NEW QUESTION 9
Which of the following terms is used to describe mechanical firestop systems?

  • A. Endothermic
  • B. Intumescent
  • C. Ablative
  • D. Elastomeric

Answer: D

NEW QUESTION 10
A third 90-degree bend may be permitted in a conduit run if the run does NOT exceed _______ ?

  • A. 5 m (16.5')
  • B. 10 m (33')
  • C. 15 m (50')
  • D. 30 m (100')

Answer: B

NEW QUESTION 11
Which of the following is used to express system gain and loss?

  • A. Ohms
  • B. Henries
  • C. Farads
  • D. Decibel (dB)

Answer: D

NEW QUESTION 12
Which of the following is used to equalize potential differences between the SBB on the same floor?

  • A. TBB
  • B. BBC
  • C. RBB
  • D. TEBC

Answer: B

NEW QUESTION 13
What is the minimum recommended height that should be used when mounting a plywood back board in a telecommunication space?

  • A. 100 mm (4")
  • B. AFF 150 mm (6")
  • C. AFF 200 mm (8")
  • D. AFF 300 mm (12") AFF

Answer: C

NEW QUESTION 14
Which of the following is a benefit of air-blown optical fiber cable?

  • A. It requires less testing than other types of cables
  • B. It can be recovered and reused
  • C. It is significantly cheaper than other types of cables

Answer: B

NEW QUESTION 15
Unqualified workers must stay AT LEAST ______ from exposed energized conductors operating at 300 to 50,000 V.

  • A. 0.3 m (1')
  • B. 3 m (10')
  • C. 15 m (50")
  • D. 30 m (100')

Answer: B

NEW QUESTION 16
A third 90-degree bend may be permitted in a conduit run if one of the bends is located within ______ of the cable feed end?

  • A. 300 mm (12")
  • B. 375 mm (15")
  • C. 450 mm (18")
  • D. 483mm (19")

Answer: A

NEW QUESTION 17
Which of the refers to a rule or set of rules intended to endure safety during the installation and use of materials, components, fixtures, systems, premises and related subjects?

  • A. Standard
  • B. Directive
  • C. Code
  • D. Regulation

Answer: C

NEW QUESTION 18
What is the specified performance level for Category 6 cable?

  • A. 100 MHz
  • B. 250 MHz
  • C. 500 MHz
  • D. 600 MHz

Answer: B

NEW QUESTION 19
Which of the following is used to establish a 0 volt (V) reference for ac electrical power systems?

  • A. Alternating current (AC) grounding electrode system
  • B. Telecommunication bonding infrastructure
  • C. Equipment grounding system

Answer: A

NEW QUESTION 20
What is the recommended minimum amount of aisle space between and around equipment?

  • A. 0.6 m (2')
  • B. 1 m (3.3')
  • C. 1.2 m (4')
  • D. 1.52 m (5')

Answer: B

NEW QUESTION 21
......

100% Valid and Newest Version IN101_V7 Questions & Answers shared by Surepassexam, Get Full Dumps HERE: https://www.surepassexam.com/IN101_V7-exam-dumps.html (New 116 Q&As)