High value 300-360 Dumps 2021

Your success in is our sole target and we develop all our in a way that facilitates the attainment of this target. Not only is our material the best you can find, it is also the most detailed and the most updated. for Cisco 300-360 are written to the highest standards of technical accuracy.

Cisco 300-360 Free Dumps Questions Online, Read and Test Now.

NEW QUESTION 1
You must perform a Layer1 survey by using Metageek Chanalyzer on the current operating mode is configured for Cisco CleanAir AP?

  • A. Local
  • B. SE-connect
  • C. Monitor
  • D. Sniffer

Answer: A

NEW QUESTION 2
You must upgrade a data- based wireless network to support Voice over Wireless. Which RSSI measurement do you use to redesign the wireless network?

  • A. -65 dBm
  • B. -72 dBm
  • C. -75 dBm
  • D. -67 dBm

Answer: D

NEW QUESTION 3
A hospital environment was designed to guarantee RF coverage at or better than -67 dBm in the 5 GHz spectrum. The customer mandates that RRM be used for DCA and TPC in both bands. After deployment, why do many of the legacy 802.11b/g devices have difficulty maintaining connectivity?

  • A. Excessive co-channel interference in the 2.4 GHz band exists.
  • B. Excessive overlapping channels in the 2.4 GHz band exists.
  • C. TPC drastically reduces Tx power in the 2.4 GHz band.
  • D. TCP drastically increases Tx power in the 2.4 GHz band.

Answer: D

NEW QUESTION 4
What is the Cisco-recommended cell overlap percentage for a typical RToWLAN network design?

  • A. 5 to 10
  • B. at least 20
  • C. a maximum of 20
  • D. at least 50

Answer: B

NEW QUESTION 5
Which three things do you need to consider prior to performing a wireless site survey? (Choose three.)

  • A. The time required to acquire any additional infrastructure components.
  • B. The time required to survey each potential AP location.
  • C. The time required to assess application server locations at the customer facility.
  • D. The type of wireless survey tools required to perform the site survey.
  • E. The time required to assess customer WLAN density and throughput requirements.
  • F. The time required to utilize the design mode in Cisco WCS to prepare a preliminary WLAN design to reduce on-site survey time.

Answer: BDE

NEW QUESTION 6
When designing a large, high-availability wireless network, what changes to a mobility- group would create less load on the controllers while maintaining the same mobility messages?

  • A. remove unnecessary controllers from the mobility-group to cut down on the controller's messaging load
  • B. separate the controllers into different mobility-groups per controller to only send relevant messaging to controllers in different groups
  • C. configure mobility-group multicast messaging
  • D. configure the controllers into separate RF-Groups from the mobility-groups to cut down on controller processing load

Answer: C

NEW QUESTION 7
During a post-deployment survey, the wireless engineer notices that offices in surrounding suites also have wireless networks and the 2.4 Ghz band is highly utilized Which configuration must the engineer make on the wireless network using this new information?

  • A. Disable 802.11 b/g data rates.
  • B. Enable Band Sect in the WLC
  • C. Disable RRM in the WLC.
  • D. Enable rogue access point containment.

Answer: D

Explanation: Monitoring Rogue Access Point Alarms
Rogue access point radios are unauthorized access points detected by one or more Cisco lightweight access points. This page displays rogue access point alarms based on the severity you clicked in the Alarm Monitor.

NEW QUESTION 8
An engineer installed a 3702 AP and is getting power from the switch. What is the reason for getting 3x3 MIMO instead of 4x4?

  • A. 802.1p
  • B. 802.3af
  • C. 802.11e
  • D. 802.3at

Answer: B

NEW QUESTION 9
Which option is an enhancement of enabling WMM on an AP?

  • A. All access classes use the same IEEE 802.11 sequence number.
  • B. It disables U-APSD Power Save.
  • C. Each access class has its own IEEE 802.11 sequence number.
  • D. CAC is reserved for voice calls only.

Answer: C

NEW QUESTION 10
An engineer is determining the signal levels for the wireless cells. Which signal-to-noise ratio is an optimal configuration to achieve?

  • A. minimum SNR of -33 dBm
  • B. minimum SNR of -25 dBm
  • C. minimum SNR of 25 dB
  • D. minimum SNR of 33 dB

Answer: C

Explanation: The minimum recommended wireless signal strength for voice applications is -67 dBm and the minimum SNR is 25 dB.

NEW QUESTION 11
An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services. Which of the following is a requirement for the design?

  • A. overlapping -72 dBm coverage from two access points
  • B. overlapping -67 dBm coverage from two access points
  • C. continuous -67 dBm coverage from one access point
  • D. continuous -72 dBm coverage from one access point

Answer: C

NEW QUESTION 12
A customer has restricted the AP and antenna combinations for a design to be limited to one model integrated antenna AP for carpeted spaces and one model external antenna AP, with high gain antennas for industrial, maintenance, or storage areas. When moving between a carpeted area to an industrial area, the engineer forgets to change survey devices and surveys several APs. Which option is the best to reduce the negative impact of the design?

  • A. Deploy the specified access points per area type.
  • B. Resurvey and adjust the design.
  • C. Increase the Tx power on incorrectly surveyed access points.
  • D. Deploy unsurveyed access points to the design.

Answer: B

NEW QUESTION 13
Which two tool in the Cisco Prime Infrastructure can you use to identify whether a floor area can support a new VoIP system? (choose two)

  • A. Location Readiness
  • B. Planning Mode
  • C. Voice Planner
  • D. Voice Readiness
  • E. Voice Audit

Answer: AD

NEW QUESTION 14
You are planning the coverage for wireless VoIP by using Ekahau. Which signal strength does Ekahau recommend using for VoIP?

  • A. -84 dBm
  • B. -76 dBm
  • C. -67 dBm
  • D. -53 dBm

Answer: C

Explanation: Each vendor has their own recommended signal strength for a given data rate or application. For instance, one vendor may recommend designing their VoIP solution at -67 dBm (perhaps the most widely-used value for VoIP deployment if I had to choose one), while another may say -70 dBm. In most cases the values will differ only by a couple dB.
https://www.ekahau.com/blog/2015/01/13/ekahau-site-survey-heatmap-visualizations-part-2-signalstrength/

NEW QUESTION 15
An engineer is assigned to provide wireless coverage in a provincial capital building. Due to the age and historic nature of the building, the ability to run new copper Ethernet cable to desired AP locations is limited. Which requirement should the engineer specify to overcome this restriction?

  • A. Deploy access points where the survey indicates and connect them via fiber optic cable, using a media adapter, and locally provide power.
  • B. Deploy access points to each phone location converting two spare pairs of copper from the phone line to Ethernet and locally provide power.
  • C. Deploy access point devices where limited cable can be run or exists and connect high-gain antennas and increase Tx power to increase cell size.
  • D. Deploy RAP where limited cable can be run or exists, and extend coverage using MAP.

Answer: D

NEW QUESTION 16
What RF phenomenon results from a presence of metallic I-beams, conveyor belts, chain-link fences, and metallic shelves found in a warehousing environment?

  • A. scattering
  • B. absorption
  • C. free path loss
  • D. multipath

Answer: D

NEW QUESTION 17
An engineer has added an access point to a deployment after a post-installation site survey. The engineer then notices that there has been an increase in co-channel interference and retransmissions. Which two features can help mitigate the issue? (Choose two.)

  • A. Coverage Hole Detection
  • B. Transmit Power Control
  • C. Enhanced Distributed Channel Access
  • D. Cisco Compatible Extensions
  • E. Dynamic Channel Assignment

Answer: CE

NEW QUESTION 18
You are designing a wireless network that contains many different types of wireless clients. How do you conduct a survey to ensure a consistent experience for all of the wireless clients?

  • A. by using the client that has the highest RF properties
  • B. by using the client that is used most by the company
  • C. by using a client of every different type
  • D. by using the client that is used least by the company

Answer: B

NEW QUESTION 19
A network installation on the site with ID 331372269 has been determined to be potentially hazardous to install. Which regulatory body must be consulted to ensure safety during the installation?

  • A. FCC
  • B. HIPPA
  • C. PCI
  • D. OSHA

Answer: D

100% Valid and Newest Version 300-360 Questions & Answers shared by prep-labs.com, Get Full Dumps HERE: https://www.prep-labs.com/dumps/300-360/ (New 168 Q&As)