Cisco 300-080 Exam Dumps 2021

It is impossible to pass Cisco 300-080 exam without any help in the short term. Come to us soon and find the most advanced, correct and guaranteed 300-080 Study Guides. You will get a surprising result by our 300-080 Braindumps.

Also have 300-080 free dumps questions for you:

NEW QUESTION 1
What does the debug output show? Refer to the exhibit.
300-080 dumps exhibit

  • A. a DSP farm profile shutdown
  • B. a DSP farm profile registration failure due to a TCP connection error
  • C. a DSP farm profile registration failure Message due to a mismatched name
  • D. that SCCP is not activated

Answer: C

NEW QUESTION 2
What does this trace indicate? Refer to the exhibit.
300-080 dumps exhibit

  • A. a disconnected call
  • B. a Completed call setup
  • C. a failed call setup
  • D. an interrupted call setup

Answer: B

NEW QUESTION 3
When parsing trace output after the call routing decision and path selection have been made, which two records can be found in the CCM|RouteList? (Choose two.)

  • A. PretransfromDigitString
  • B. CallingPartyNumber
  • C. PretransformCallingPartyNumber
  • D. RouteListName
  • E. findLocalDevice
  • F. RouteListCdrc :

Answer: DF

NEW QUESTION 4
You have 50 hardware MTP resources and 200 software MTP resources. You want to use hardware resources first, but software is being useDFirst. Where can you confirm the MTP selection order?

  • A. Media Resource Group List
  • B. Cisco Unified Real-Time Monitoring Tool
  • C. MTP list
  • D. phone device pool
  • E. calling search space
  • F. MGCP gateway

Answer: A

NEW QUESTION 5
During a Conference that is hosted on a Cisco TelePresence Server, which three circumstances determine that some participants do not have video, but they do have audio? (Choose three.)

  • A. The participants have no video component.
  • B. No free screen licensing ports are available.
  • C. No video ports are available in a slave Cisco TelePresence Server configuration.
  • D. The maximum number of participants is exceeded.
  • E. In all Cisco TelePresence deployments, some participants are connected only via audio.
  • F. No video ports are available in a single Cisco TelePresence Server configuration.

Answer: BCF

NEW QUESTION 6
After you deploy a hardware transcoder, users without a Common codec are unable to complete cafe to one another. Which two actions must you take (Choose two.)

  • A. Use RTMT to verify mat transcoder resources are available
  • B. verify that all SIP trunks are registered within Cisco Unified Communications Manager
  • C. verify that media resources are assigned to the transcoder
  • D. verify that the transcoder registered with Cisco Untied Communications Manage.
  • E. verify that the transcoder is running the latest firmware anDFlash NVRAM

Answer: AD

NEW QUESTION 7
Cisco TelePresence Systems that are calling from a Cisco Unified Communications Manager cluster to an

  • A. H.323 registered device on a Cisco Expressway Control do not wor
  • B. However, calls from the H.323 Expressway registered devices to the same Cisco Unified Communications Manager registered systems do work.What are two possible reasons? (Choose two.)
  • C. The SIP trunk has not enabled bidirectional mode.
  • D. The call from Cisco Unified Communications manager to the Cisco Expressway Control does not match any search rule.
  • E. Calls from Cisco Unified Communications Manager add “.5060” or “.5061” after the SIP address, unlike the Cisco Expressway Control.
  • F. The Cisco Expressway Control is registered in the wrong partition.
  • G. Both systems do not support TLS encryption

Answer: AC

NEW QUESTION 8
What is the default directory format that you need to specify for Default TFTP MOH File Path field on the Cisco Unified Communications Manager (CUCM) server?

  • A. MoH
  • B. TFTPPATHMoH
  • C. TFTPPATH
  • D. MoHTFTPPATH
  • E. TFTPPATHMoHFiles
  • F. MoHFiles

Answer: C

NEW QUESTION 9
300-080 dumps exhibit
Refer to the exhibit. Audio calls from ACSF device fail. Which command set likely resolves the issue?

  • A. configure terminal voice-port 0/1/0:15 output attenuation -4
  • B. configure terminal controller e1 0/1/0 bearer-cap speech
  • C. configure terminal interface serial 0/1/0:15 output attenuation -4
  • D. configure terminal voice-port 0/1/0:15 bearer-cap speech

Answer: B

NEW QUESTION 10
Refer to the exhibit.
300-080 dumps exhibit
Local 10-digit dialing in the North American Numbering Plan to area Code 456 is failing. Which two changes are needed to enable 10-digit dialing? (Choose two.)

  • A. Change dial peer 210 to destination-pattern 456.......
  • B. Change dial peer 210 to destination-pattern 9456.......
  • C. Change dial peer 210 to port 0/0/0:23.
  • D. Remove the command prefix 456 from dial peer 210.

Answer: BC

NEW QUESTION 11
Refer to topology and Exhibits below:
300-080 dumps exhibit
300-080 dumps exhibit
300-080 dumps exhibit
300-080 dumps exhibit
Which command can be used to obtain the status of an MGCP gateway from the IOS device, as shown in the given output?

  • A. show mgcp registration
  • B. show mgcp-gw
  • C. show mgcp connection
  • D. show ccm-manager

Answer: D

NEW QUESTION 12
In an MCU call with three Cisco TelePresence MX800 systems and a mobile phone calling in, the three TelePresence MX800 systems suddenly experience low audio levels, but the mobile phone audio levels are
correct. What can you do to correct this issue?

  • A. Turn off the audio processors on the TelePresence MX800.
  • B. Use the mobile phone audio option on the TelePresence MX800 to adjust the mobile phone levels.
  • C. Mobile phone audio levels can vary, so you cannot correct the issue.
  • D. Turn on AGC on the MCU to adjust the audio levels.
  • E. Turn on ALG on the MCU to adjust the audio levels.
  • F. Turn on the Auto Adjust levels under "Settings > Audio" on the MCU.

Answer: D

NEW QUESTION 13
You have configured a new MGCP gateway on your Cisco Unified Communications Manager servers but the endpoints are shown with status "None”.
What are two possible solutions for this registration issue? (Choose two)

  • A. Configure the voice-VLAN interface of the MGCP gateway with mgcp-gateway voip interface command to set the source IP address of the MGCP packets correctly.
  • B. Ensure that you have configured the mgcp call-agent command with the Cisco Unified Communications Manager server address or hostname.
  • C. Enable the endpoint voice interface for backhauling in interface configuration mode with the isdn bind-l3 ccm-manager command
  • D. Ensure that you have configured the ccm-manager call-agent command with the correct Cisco Unified Communications Manager server address or hostname.
  • E. Activate the MGCP Feature service on all call-processing servers in the cluster.

Answer: BD

NEW QUESTION 14
A network administrator for the ACME Corporation is adding a new remote site to the existing network infrastructure. DHCP is already provisioneDFor this site. When the administrator connects the Cisco IP phone to the network, the phone keeps displaying the word "Registering." The administrator is able to ping the phone's IP address from a laptop. Which two actions should the administrator take to troubleshoot the problem? (Choose two.)

  • A. Check DHCP option 150.
  • B. If a laptop is connected to the PC port, check whether the network driver on the PC is up to date.
  • C. Check network connectivity between IP phone at the remote site and Cisco Unified Communications Manager server at the main site.
  • D. Check the NTP configuration on the phone.
  • E. Check DHCP option 67.

Answer: BC

NEW QUESTION 15
A system administrator receives a help ticket stating that users at a remote office are unable make three-way calls What should the administrator do in the cisco Unified Communications Manager configuration to troubleshoot the issue?

  • A. Check the media resources for a registered conference bridge anDEnsure that it is added to the correct region for that office.
  • B. Check the media resources for a registered Media Termination point anDEnsure that it is added to the correct Media Resource Group for that office.
  • C. Check the media resources for a registered Media Termination point anDEnsure that it is assigned to a location for that office.
  • D. Check the media resources for a registered conference bridge anDEnsure that it is assigned to the right Media Resource Group for that office.

Answer: D

NEW QUESTION 16
Refer to the exhibit.
300-080 dumps exhibit
An engineer is troubleshooting an outbound call and needs to see each step of the dial plan as it is being parsed in the system. The engineer is not able to see all of the steps in the trace output. How can this problem be resolved?

  • A. Change the Digit Analysis Complexity to Translation And Alternate Pattern Analysis.
  • B. Change the SDL Trace Max File Size to a higher number because it is not large enough to display dial plan steps.
  • C. Change the SSL TraceType Flag to 0x9000EC44.
  • D. Change the SSL Trace Flush Immediately to True.

Answer: A

NEW QUESTION 17
Drag the network-related video issue on the left to its root cause on the right.
300-080 dumps exhibit

    Answer:

    Explanation: 300-080 dumps exhibit

    NEW QUESTION 18
    Users are complaining of problems when they make SIP calls by dialing URIs. To help users complete calls, what must you do?

    • A. Adjust the URI lookup policy to case desensitive.
    • B. Adjust the URI lookup policy to case sensitive.
    • C. Adjust the URI lookup policy to case insensitive.
    • D. Adjust the URI lookup policy to case nonsensitive.

    Answer: C

    P.S. Certstest now are offering 100% pass ensure 300-080 dumps! All 300-080 exam questions have been updated with correct answers: https://www.certstest.com/dumps/300-080/ (219 New Questions)