Breathing 210-065 Exam Questions 2021

NEW QUESTION 1
Refer to the exhibit.

Which tab can be used in order to check the call statistics for the Cisco TelePresence Codec C60?

• A. Diagnostics
• B. Configuration
• C. Call Control
• D. Maintenance
• E. The GUI cannot be used to view call statistics.

Answer: C

NEW QUESTION 2
Refer to the exhibit.

When this alarm is seen, what is the maximum number of registrations that a Cisco VCS can support?

• A. 2500
• B. 50
• C. 3

Answer: C

NEW QUESTION 3
Refer to the exhibit.

The screenshots show outputs from the xStatus of a Cisco TelePresence endpoint and the VCS registrations. What are the protocol and direction of the call, the called party, and the transmit rate of the call?

• A. h.323, incoming, 5919*2345, 1152 Kb/s
• B. h.323, outgoing, 5919*2345, 1152 Kb/s
• C. h.323, incoming, 5919*2345, 768 Kb/s
• D. sip, incoming, 5919*2345, 768 Kb/s
• E. sip, outgoing, 5919*2345, 768 Kb/s

Answer: B

NEW QUESTION 4
ACisco engineer needs to provide digital media for the lobby of a company. Which Cisco Digital Media component should the engineer use?

• A. Cisco Cast
• B. Cisco Digital Signs
• C. Cisco DMP
• D. Cisco Show and Share
• E. Cisco IP TV

Answer: B

NEW QUESTION 5
Refer to the exhibit.

When the administrator clicks the ticket number of any of the open tickets, which two actions are presented to the administrator? (Choose two.)

• A. ignore ticket
• B. acknowledge ticket
• C. delete ticket
• D. close ticket
• E. escalate ticket

Answer: AB

NEW QUESTION 6
Which option is an immersive endpoint?

• A. Cisco TelePresence EX90
• B. Cisco TelePresence TX9000
• C. Cisco TelePresence SX10
• D. Cisco TelePresence DX70

Answer: C

NEW QUESTION 7
Which action ensures prioritization of voice over data traffic?

• A. voice and data VLAN on different subnets with QoS classification
• B. voice and data VLAN on same subnets without QoS classification
• C. signaling and media traffic marked with Layer 2 CoS and Layer 3 DSCP mappings
• D. signaling and media traffic marked with Layer 2 DSCP and Layer 3 CoS mappings

Answer: C

NEW QUESTION 8
You have been informed from the field that a new Cisco TelePresence video endpoint has been deployed with an IPv4 address of 172.28.254.45. You need to check for connectivity from the Cisco Unified Communications Manager server. Which command should be entered to check for network connectivity?

• A. utils network traceroute newsystem.domain254.local
• B. utils network ping 172.28.254.45
• C. ping 172.28.254.45
• D. traceroute 172.28.255.255
• E. utils network host cucm.osl147.local

Answer: B

NEW QUESTION 9
When connecting to a pan-tilt-zoom camera to a C-Series codec, what type of cable must be used for camera control?

• A. an Ethernet crossover cable (RJ45-to-RJ45)
• B. an Ethernet cable (RJ45-to-RJ45)
• C. a serial cable (DB25-to-DB9)
• D. a VISCA cable (DB9-to-RJ45)

Answer: D

NEW QUESTION 10
A company wants to enable a mobile user to connect to the corporate network to access calls, messages, video conferencing, and web collaboration. Which product provides these features for the user?

• A. Cisco WebEx Connect
• B. Cisco Unified Presence
• C. Cisco TelePresence SX20
• D. Cisco Jabber

Answer: D

NEW QUESTION 11
The microphone on a Cisco TelePresence System 3000 is switching incorrectly to a camera that does not have an active speaker. What is the first step that an engineer should take to troubleshoot this issue?

• A. Check whether the microphone is properly plugged in.
• B. Run the microphone calibration procedure.
• C. Plug all microphones into the primary codec.
• D. Check whether the cable from the microphone is plugged into the correct receptor on the codec.

Answer: B

NEW QUESTION 12
An engineer wants to stream Cisco TelePresence high-definition video to another location. The stream must be connected to an HDMI input on a display. Which two components, at minimum, are required to provide this functionality? (Choose two.)

• A. Cisco Media Experience Engine 3500
• B. Cisco TelePresence Content Server
• C. Cisco Digital Media Player
• D. Cisco Digital Media Manager
• E. Cisco TelePresence Server

Answer: BC

NEW QUESTION 13
Endpoint for immersive telepresence:

• A. EX 90
• B. TX 9000
• C. SX 10
• D. DX 70

Answer: B

NEW QUESTION 14
ACisco TelePresence System 1300 Series endpoint is in the process of booting and the engineer notices a red "X" on the screen for Step 6 in the boot process. What does this red "X" indicate?

• A. The endpoint failed to load its firmware.
• B. There is an error with compact flash.
• C. The endpoint could not obtain an IP address via DHCP.
• D. The touch panel is malfunctioning.

Answer: B

NEW QUESTION 15
Which function does FECC provide?

• A. the ability to transfer calls between the SIP and H.323 protocols
• B. the ability to pan, tilt, and zoom the camera at the far end
• C. the ability to switch between content channels
• D. the ability to send DTMF tones

Answer: B

Explanation: Topic 3, Troubleshooting and Support

NEW QUESTION 16
Which CLI command can be used to reset the Cisco TelePresence System 500-32 personal video system to a factory condition?

• A. utils factory reset 2
• B. utils system factory init
• C. xcommand defaultvalues set level: 2
• D. xconfiguration default factory
• E. utils reset factory
• F. xcommand SystemUnit FactoryReset

Answer: B