All About Pinpoint 1Z0-597 Real Exam

NEW QUESTION 1
Using the logical domainconfiguration below,what is the domain and virtual CPU corresponding to physical CPU number 5?

• A. domain primary, virtual CPU number 0
• B. domain primary, virtual CPU number 1
• C. domain ldg2, virtual CPU number 0
• D. domain ldg1, virtual CPU number 1

Answer: D

NEW QUESTION 2
As part of a server consolidation project, a customer would like to run Solaris 9-based applications on a SPARC T4 server. What technology is required?

• A. Oracle VM Server for SPARC
• B. Oracle Solaris Containers
• C. Dynamic Domains
• D. Oracle VirtualBox

Answer: A

NEW QUESTION 3
During the acclimatization process, what is the maximum positive or negative temperature
gradient that is permitted for multi-layer boards?

• A. Approximately 2° C (4° F) per hour
• B. Approximately 4° C (7° F) per hour
• C. Approximately 6° C (11° F) per hour
• D. Approximately 8° C (4° F) per hour

Answer: A

NEW QUESTION 4
According to the Enterprise Installation Standards (EIS), what is the recommended minimum amount of memory that should be allocated to the control domain?

• A. 2 GB
• B. 3 GB
• C. 4 GB
• D. 6 GB

Answer: A

NEW QUESTION 5
You have configured DNS and have determined that the services processor serial number for your target server is 0641AMA007. What is the host name of this server?

• A. SUN-0641AMA007
• B. SUNCMM0-0641AMA007
• C. SUNCMM1-0641AMA007
• D. SUNSP-0641AMA007

Answer: A

NEW QUESTION 6
Error conditions by POST, Oracle Solaris Predictive Self-Healing (PSH), and Oracle ILOM are forward to which component for fault handling?

• A. POST
• B. Oracle VTS
• C. Oracle ILOM
• D. Oracle Solaris PSH

Answer: C

Explanation:

Reference:http://docs.oracle.com/cd/E23075_01/pdf/E23078.pdf(page 24, third para)

NEW QUESTION 7
Below is a list of boot environments available on a SPARCT4 server running Oracle Solaris 11. Which boot environment is currentlybooted?

• A. S11amp
• B. Solaris
• C. Solaris – 151a
• D. Solaris – 174

Answer: D

NEW QUESTION 8
According to the Enterprise Installation Standards (EIS), what is the minimum amount of time SunVTS should be run?

• A. 10 minutes
• B. 20 minutes
• C. 30 minutes
• D. 1 hour

Answer: D

NEW QUESTION 9
You have set up power on self test (POST) to run when the scrvrr has been reset by the user. The customer would like POST to run any error-invoked reset. How is this accomplished?

• A. Change the diagnostic level to "max" (user_reset_level = max).
• B. Change the diagnostic trigger to "error reset" (trigger = error-reset).
• C. Change the verbosity to "debug" (user_reset verbosity = debug).
• D. Change the diagnostic trigger to "power on-reset" (trigger = power-on-reset).

Answer: B

NEW QUESTION 10
Identify two specification of the Enterprise Installation Standard (EIS) for Basic Solaris.

• A. It defines the process for downloading Solaris and related patches from the Oracle support web site
• B. It requires the Installer to use the appropriate his Installation checklists when Installing Solaris
• C. It mandates that Installers use the EIS-DVD during the Installation process
• D. It provide the guidelines and patch levels for Installing Solaris 8, 9, 10, or 11

Answer: B

NEW QUESTION 11
In planning for the installation of a SPARC T4 server, you notice that a more recent version of a patch is available than what is currently on the EIS-DVD. According to the Enterprise Installation Standards (EIS) methodology, what should you do?

• A. Always install the most recent version of a patch
• B. Delay Installation until the updated patch is published to the EIS-DVD
• C. Do not Install the patch, unless instructed to do so by an EIS-Alert
• D. Never Install patches outside of the EIS-DVD

Answer: A

NEW QUESTION 12
You lost your Oracle ILOM settings after a service processor firmware update. Why?

• A. You did not enable the Preserve Configuration option.
• B. You did not back up the Oracle ILOM configuration.
• C. Oracle ILOM settings must be re-established after every firmware update.
• D. You used the Oracle ILOM web interface rather than the CLI to perform the update.

Answer: A

NEW QUESTION 13
A faulty DIMM needs to be replaced on a SPARC T4-2 server. What are two ways to determine which DIMM on a memory riser is faulty?

• A. Run the Oracle ILOM show faulty command.
• B. Run Oracle VTS software.
• C. Run the Oracle ILOM –al command.
• D. Press the Remind button on the memory riser.

Answer: AD

NEW QUESTION 14
How many XAUI (10 GbE Attachment Unit Interfaces) ports are provided per SPARC T4 processor?

• A. 1
• B. 2
• C. 3
• D. 4

Answer: B

NEW QUESTION 15
Which command lists dynamically reconfigurable hardware resources and shows their operational status?

• A. dmesg
• B. ldm ls
• C. fmadm –al
• D. cfgadm –al

Answer: D

Explanation:

Reference:http://docs.oracle.com/cd/E22985_01/html/E22986/z40019011297337.html(See step 2)

NEW QUESTION 16
As part of our test procedure plan, you need to confirm that savecore is configured correctly. Which test should you use?

• A. Explore Data Collector Test
• B. Solaris VTS Test
• C. Solaris Crash Dump Test
• D. Savecore Test

Answer: C

NEW QUESTION 17
What is Critical Thread Optimization?

• A. The ability to dynamically allocate core resources among active threads
• B. The ability to bind individual threads to a processor
• C. Part of the Processor Sets feature of Oracle Solaris that defines a group of logicalprocessors and schedules threads on them.
• D. Recognized by Oracle Solaris Scheduler as a thread that should run by itself on a single core

Answer: A

NEW QUESTION 18
When preparing to update the firmware, which two statements are true?

• A. If performed via the ILOM interface, the firmware file should reside on the system from which the browser is launched.
• B. If performed via the ILOM web interface, a TFTP server is required.
• C. If performed via the ILOM CLI, a TFTP server is required.
• D. Firmware updates can only be performed via the ILOM CLI.

Answer: B

NEW QUESTION 19
In general, when labeling a cable, the host connection should follow the format: <system name> <board no.> <slot no.> and .

• A. <port no.>
• B. <insertion point>
• C. <cable no.>
• D. <rack no.>

Answer: C

NEW QUESTION 20
System errorscan go undetected by the Oracle VTS test, since many are detected, managed, and reported by Oracle Solaris Predictive Self-Healing. What is one way to display these errors and faults?

• A. Review the VTS error file
• B. Review the output of fmdump
• C. Review the system log files
• D. Review the VTS kernel error log

Answer: D

NEW QUESTION 21
You are installing a SPARC T4 server at a customer site using a single-phase power feed. The power outlet is 15 meters (16.4 feet) from device. Which Enterprise Installation Standard (EIS) document would you have highlighted this issue prior to installation?

• A. Site audit report
• B. Test procedure plan
• C. Power routing map
• D. Server operational checklist

Answer: D

NEW QUESTION 22
......